How to wash tiles after repair: effective ways

During the repair process, tiles are covered with dust, glue, a primer and other building materials. Such consequences make housewives clutch their heads, I do not know what to do. As a rule, cleaning updated housing requires patience and attention to detail. In order to clean the floor from pollution, it is necessary to use all kinds of means, which we will talk about today. We will consider the important aspects in order and give practical recommendations.

How to wash a tile after repair: types of pollution

In the process of repairing, tiles get dirty with building materials of different structures and purposes. It is not always possible to protect the coating by first laying a plastic film or newspaper.

Hence there is a need to clean tiles from building dust, glue, grout, primer, plaster, sealant, foam, paint or lime.

Large construction stores sell special cleaning products for flooring, but they can be replaced by home methods. Consider the effective methods in order.

How to wash tiles from building dust

Perhaps one of the harmless types of pollution is construction dust. Not a single repair can do without it, so it makes sense to consider effective cleaning methods.

Before using household products, sweep the floor, collect large debris and dirt with a dry cloth.

If possible, vacuum the coating; try tearing off glue, foam and other hardened materials with a blade. After preparation, proceed to wet cleaning by choosing one of the proposed tools.

1. Lemon acid. Dilute in 7 liters. warm water 120 gr. citric acid, wait for the crystals to dissolve. Dip a rag or mop into the solution, thoroughly wash the floor from one wall to another (parallel lines). After wet cleaning, open the doors and windows, carefully ventilate the room. In addition to cleaning products, citric acid will make the tiles shiny and hide possible cracks or scratches.
2. Table vinegar. To prepare the solution, take 125 ml. table vinegar (concentration of 9%), dilute the product in 5 l. warm water, mix. Add 1 sachet of citric acid, wait for the crystals to dissolve. After that, moisten the mop in the prepared solution, carry out wet cleaning. Next, wipe the floor with a clean, dry cloth to prevent any streaks.
3. Powder "Automatic". Pour 8 liters into a bucket. hot water, pour 150 g. washing powder, mix the composition with a wooden spatula to completely dissolve the crystals. After that, moisten a rag in the solution, wipe the floor in a circular motion. When all the tiles are cleaned, wipe the cover clean, washing the rag in clean water. It is important to collect all the foam from the tile so that it does not form stains. If necessary, walk along the surface with a dry cloth.

How to wash tiles from glue

Unlike construction dust, the adhesive solution is more resistant to various cleaning agents, so the approach should be thorough.

1. Water. If the adhesive got on the tile during processing, remove it with a damp cloth and a rubber spatula. In this case, alternate the tools (spatula).
2. Ammonia. In the case of fresh hardened glue, it is important to soften the composition in time. To do this, pour 1 liter in a bucket. water, add 35 ml. ammonia (ammonia) or 100 ml.table vinegar (concentration 9%). Moisten the resulting composition with gauze, folded in several layers. It is important that it is very wet. After that, put gauze on a spot of glue, leave for 10 minutes. Scrape off the rest with a rubber tipped spatula, try not to damage the tiles.
3. Acetone. If it was not possible to prevent the glue from getting on the tile, as a result of which it froze, proceed as follows. Take an old cotton towel, soak it in nail polish remover, mortar or acetone. Put on the glue trace, wait half an hour. Periodically wet the rag in the solution. After all the manipulations, scrape off the remaining material with a spatula or blade.

How to wash tiles from grout

Grout is used to cover joints that form during tile laying. In the end, the tile looks holistic, beautiful. In addition to this, mastic for carrying out work of this type is easily washed off the surface. This cleaning option is ideal for removing soft cycle mixtures. Consider the procedure in more detail.

After you have covered the joints, wait for the grout to dry (but not completely harden). The top layer will turn whitish, this will be a signal of the beginning of cleaning. Dampen the cloth in water, go over the entire surface of the tile, washing off the grout as a whitewash.

To remove the epoxy grout from the tile surface, purchase a solvent designed specifically for this purpose from a hardware store. Without it, it is unlikely to clean the tile.

How to wash a tile from a primer

As a rule, wall cladding is carried out after laying the tiles. For this reason, white spots can often be found on tiles, which are quite difficult to clean after hardening.

1. Water. If the primer just got on the tile, wash it with warm (almost hot) water. To improve the effect, add 50 g. granulated sugar, wait for the crystals to dissolve. Dip a sponge into the solution, wipe the dirt.
2. Solvent. An effective method of cleaning is considered an industrial solvent, both automotive and construction. It is enough to moisten a cosmetic swab or a clean rag in the composition, and then wipe the trace of the primer.
3. Alkali. Get a tool that includes alkali. Dampen a napkin or rag, wipe the tile several times. Finish by wiping the tiles with table vinegar.

Universal cleaning methods

1. "White Spirit". Remove traces of mounting foam, paint, primer and other building materials with a towel dipped in White Spirit. After processing, wipe the tile with a dry cloth.
2. Means for washing windows. The most effective and affordable way to clean tiles from various kinds of contaminants. Buy a spray bottle, spray the composition on the tile, wipe dry first with a cotton cloth, then with a microfiber cloth. Perform the procedure in stages, process 1-2 square meters. m. tile at a time.
3. "Cinderella". Purchase liquid detergent from a hardware store and use it according to the instructions. After the procedure, moisten the tile with water, wipe with a sponge and polish with a soft cloth.
4. Sandpaper. Try scrubbing large pieces of primer, mounting foam, glue, etc. with sandpaper to polish your cars. Choose a degree of abrasiveness from 1000 to 2000. After the procedure, polish the coating with a velvet cloth.

It is easy to wash tiles from building materials, if you have sufficient knowledge regarding the procedure. Use acetone, vinegar, citric acid or a solvent. Remove large parts with a scraper or sandpaper.

Video: how to clean tiles from cement after repair